Flowers always brighten everyone's mood, and these coasters made with pressed flowers will definitely add some cheer to your table — even before the drinks are served. The flowers are encased in clear resin, so they look they are floating in glass. These coasters are so beautiful, they would also be perfect as gifts, or even favors for bridal showers and weddings.

pressed flower coasters

Video of the Day

Things You’ll Need

  • Pressed flowers

  • 4-inch round disk silicone mold

  • Rubbing alcohol

  • Resin mix

  • Plastic cups

  • Wooden stir sticks

  • Butane lighter

  • Tweezers

  • Adhesive rubber pads

materials

Step 1: Press Flowers

You can purchase dried, pressed flowers at the crafts store or online, but if you wish to press your own flowers, place them between parchment paper in a heavy book like a dictionary. Close the book and place additional books on top to put extra weight on the flowers. Let them dry and flatten for 7 to 10 days. Flowers that are already flat, e.g., daisies, work better than fuller buds like roses.

press flowers

Step 2: Clean the Silicone Mold

For this project, you'll need a 4-inch diameter round disk silicone mold. Wash it well in soap and water and allow to dry thoroughly. Then remove any additional residue with a lint-free paper towel and rubbing alcohol.

silicone mold

Step 3: Mix Resin

Resin typically comes in two parts — the resin and the hardener. Mixing the two parts creates a clear, glass-like surface when it hardens. (Different brands of resin have varying instructions in terms of resin and hardener ratios. The brand I used required a 1 to 1 ratio, so this tutorial reflects that. Check the specific instructions for the brand of resin you select.) Pour an equal amount of resin and hardener in two separate plastic cups. I marked a black line on both to guide my measuring.

resin ratio

Pour the contents of the two cups into a third, mixing with a wooden stir stick for two minutes. (Again, check the instructions for your specific brand of resin.) Be sure to scrape the sides and bottoms of the cup while stirring.

stir resin

Then pour the mixture into a fourth, clean cup and mix for an additional minute with a new stir stick.

fourth cup

Step 4: Pour First Layer of Resin

We'll pour the resin in two layers so that the pressed flowers are encased between the layers. Pour the resin in the molds about a third of the way.

pour resin

Step 5: Remove Bubbles

Air bubbles created while mixing will be evident in the resin, and more bubbles will begin forming in the mold. To degas the bubbles, run the flame of a butane lighter about two inches above the surface of the resin. Carbon dioxide, not heat, is what degasses the bubbles, so another method is to blow on the resin with a straw. Even after you remove the bubbles, more will form in the first 15 minutes, so be vigilant and degas as they form.

degas bubbles

Step 6: Add Pressed Flowers

After the resin has sat in the mold for about 15 minutes, it's time to add the flowers. Trying to maneuver the delicate pressed flowers with your fingers can be difficult, so lift them up individually with tweezers.

tweezers

Arrange the flowers upside down on the resin, as the bottom of the mold will actually be the top of the coaster.

upside down flowers

Position the larger pieces and greenery on top of the flowers, as these will be on the bottom of the coasters when flipped over. This way, they won't block the flowers in front.

greenery

All the pressed flowers need to make contact with the resin so they are locked in place when the resin hardens. Use a toothpick to press down any flowers or leaves that aren't touching resin.

toothpick

Let the resin harden for about four hours to allow the flowers to set.

flowers in resin

Step 7: Pour the Second Layer of Resin

Mix another batch of resin as you did before. Pour the resin into the molds on top of the first layer with the flowers. You don't need to go all the way to the top of the mold, just far enough to completely cover the flowers.

second layer

Remove any bubbles that form in this second layer of resin with your butane lighter.

lighter

Let the resin cure for a full 24 hours.

cure resin

Step 8: Remove Coasters from Molds

After 24 hours, peel the molds back and remove the coasters. They will pop right out. This will be the first time you'll see your flower designs right side up, so take a moment to marvel at the beauty.

remove coasters

Step 9: Apply Rubber Pads

To protect tabletops and keep the coasters from sliding around, place three or four clear rubber pads with adhesive backing on the bottom of the coasters.

rubber pads

You'll want to make sets of these coasters for everyone on your gift list.

pressed flower coasters

LEAVE A REPLY

Please enter your comment!
Please enter your name here